North Repair Parts

Brand
Sort
Search This Page
Fixmykite.com North Hyperflow inflate Valve
1 of 4

NORTH HYPERFLOW INFLATE VALVE works on new North kites starting in 2020 and beyond. Valves also work on Slingshot, Cabrinha, and Eleveight kites. Made with Tear-Aid to work with any bladder

How to install a fixmykite.com self stick valve?

1. Valve Removal:
 If replacing valve, carefully peel off old valve. If old valve does peel off, cut around circumference of valve to remove
2. Cleaning: Wipe area where valve will be placed with provided alcohol swab. DRY COMPLETELY WITH A CLEAN PAPER TOWEL.
3. Peel and Stick: Lay bladder out flat. If possible, have a friend lightly hold bladder on table or other smooth even surface. Peel off paper backing, center valve over hole, and place valve on bladder.
4. Press: Press valve from center outward to remove air bubbles and ensure proper adhesion and creases.

*Pro Tip- Use a hair dryer to heat the valve. This makes it easier to remove the valve. After placement of the Fixmykite self stick valve use the hair dryer again to warm the adhesive. Press the valve from the center out massaging and stretching creating positive adhesion. Be careful not to overheat the bladder or new valve.



If you're unsure which value is required for your replacement project, please do not hesitate to contact us. Email:  [email protected] or Call 361-883-1473


Add Velcro Option
The "Add Velcro" option provides you with attached Velcro at the base of the valve just as you would see with the original factory bladder.  This part of the valve goes on the inside of the kite casing; the Velcro prevents the bladder from twisting when tightening the screw-cap. 

MEGA Option: The MEGA valve option refers to the size of the TEAR-AID PATCH ONLY.  MEGA patches are 4 inches in diameter as opposed to the standard valve patch which has a 3? diameter. This extra inch means 77% more adhesive base and surface area compared to the standard valve patch size. The MEGA-valve patch is necessary when the old valve is cut from the bladder or leaves a tear during removal. The additional surface area provided by the Mega valve Tear-Aid patch allows quick and easy bladder repair eliminating the need for an additional bladder patch. The Mega Valve Patch can also be used if the valve area of the bladder is warped.

If your old valve(s) cleanly peel(s) off, a larger Mega patch in most cases isn?t necessary.

Add Bladder Patch Install Kit Option
The Bladder Patch Install Kit is for use when your old valve has to be cut out of the bladder leaving a hole larger than the valve. If your old valve peels off of your bladder easily, you do NOT need the bladder patch kit. The Bladder Patch Install Kit includes a 4 X 4 bladder patch protective piece and a 6x6-Inch (15.24 x 15.24cm) adhesive patch.


 

$23.95
Fixmykite.com North Hyperflow inflate Valve - Base Only

NORTH HYPERFLOW INFLATE VALVE works on new North kites starting in 2020 and beyond. Valves also work on Slingshot, Cabrinha, and Eleveight kites. Made with Tear-Aid to work with any bladder

How to install a fixmykite.com self stick valve?

1. Valve Removal:
 If replacing valve, carefully peel off old valve. If old valve does peel off, cut around circumference of valve to remove
2. Cleaning: Wipe area where valve will be placed with provided alcohol swab. DRY COMPLETELY WITH A CLEAN PAPER TOWEL.
3. Peel and Stick: Lay bladder out flat. If possible, have a friend lightly hold bladder on table or other smooth even surface. Peel off paper backing, center valve over hole, and place valve on bladder.
4. Press: Press valve from center outward to remove air bubbles and ensure proper adhesion and creases.

*Pro Tip- Use a hair dryer to heat the valve. This makes it easier to remove the valve. After placement of the Fixmykite self stick valve use the hair dryer again to warm the adhesive. Press the valve from the center out massaging and stretching creating positive adhesion. Be careful not to overheat the bladder or new valve.



If you?re unsure which value is required for your replacement project, please do not hesitate to contact us. Email:  [email protected] or Call 361-883-1473


Add Velcro Option
The "Add Velcro" option provides you with attached Velcro at the base of the valve just as you would see with the original factory bladder.  This part of the valve goes on the inside of the kite casing; the Velcro prevents the bladder from twisting when tightening the screw-cap. 

MEGA Option: The MEGA valve option refers to the size of the TEAR-AID PATCH ONLY.  MEGA patches are 4 inches in diameter as opposed to the standard valve patch which has a 3? diameter. This extra inch means 77% more adhesive base and surface area compared to the standard valve patch size. The MEGA-valve patch is necessary when the old valve is cut from the bladder or leaves a tear during removal. The additional surface area provided by the Mega valve Tear-Aid patch allows quick and easy bladder repair eliminating the need for an additional bladder patch. The Mega Valve Patch can also be used if the valve area of the bladder is warped.

If your old valve(s) cleanly peel(s) off, a larger Mega patch in most cases isn?t necessary.

Add Bladder Patch Install Kit Option
The Bladder Patch Install Kit is for use when your old valve has to be cut out of the bladder leaving a hole larger than the valve. If your old valve peels off of your bladder easily, you do NOT need the bladder patch kit. The Bladder Patch Install Kit includes a baggie of talcum powder and a 6x6-Inch (15.24 x 15.24cm) adhesive patch.


 

$13.95
North OEM Replacement Line Set - 22m / 12m + 10m

North Replacement Standard Spare Line set - 22m Overall Length

12m + 10m Dyneema SK99 line extensions enable you to customise your line length for wave riding or tighter kiteloops. The Navigator Control System is supplied with 22m Lines, with a split at 12m, which is far enough for the bar to travel to completely depower our largest kite when you flag out. Remove the standard 10m top section of line and 12m lines are ideal for schools to teach with and for foil racing. Shorter 8m + 2m line extensions are also available as an accessory for those wanting 18m or 20m lines for wave riding or tighter kiteloops.

$149.99
North OEM Line Extension Set

North Line Extension set

Dyneema SK99 line extensions enable you to customise your line length for wave riding or tighter kiteloops. The Navigator Control System is supplied with 22m Lines, with a split at 12m. If you want to lengthen your lines, just choose what length works best for you!

Includes:   
4 Lines with spliced loops on both ends

Features

  • SK99 Dyneema lines
  • Spliced with stitched loops on all ends
  • Pre-Stretched

$29.95
North OEM Short Spare Line Set - 10m (8m + 2m)

North Short Spare Line Set - 10m

8m + 2m Dyneema line extensions for those wanting custom 18m or 20m lines for wave riding or tighter kiteloops. The Navigator Control System is supplied with 22m Lines, with a split at 12m, which is far enough for the bar to travel to completely depower our largest kite when you flag out. Remove the standard 10m top section of line and 12m lines are ideal for schools to teach with and for foil racing.

Includes:     

  • 2x 8m Lines (Green), 2x 8m Lines (Grey), 2x 2m Lines (Green), 2x 2m Lines (Grey), Line Winder

$99.00
North Kiteboarding Navigator Bar Cleat

North Navigator Cleat Kit

Replacement cleat kit for North Navigator control bar.

Includes:     Cleat, Base, 2x screws

$22.00
North Kiteboarding Navigator Bar Landing / Flagout Line

North Navigator Landing Line / Flagout Line

Top quality, German-made, extremely high wear Dyneema replacement trim line for the Navigator Control System.

Includes Line, Stopper ball and swivel.

$12.00
North Kiteboarding Power / Trimmer Bracket
North Kiteboarding replacement Power Bracket for Navigator control system.
$18.00
North Kiteboarding Navigator Bar Connect Quick Release
North Navigator Bar Connect Quick Release

Security and performance in all conditions. Our patented and ISO-approved Connect Quick Release (QR) raises the bar in kite control system safety. The red QR handle has been ergonomically designed to fit in your hand comfortably for an industry-standard push away release. All loaded or running surfaces feature highly polished 316 stainless steel and low-friction components. The stretchy, larger diameter bungee inside the QR helps reduce accidental release.

Works on 2019-2022 Navigator bars

North Part: 85007.220038
$110.00
North Kiteboarding Navigator Release Pin O-Ring - Sold Individually
1 of 2

North Navigator Release Pin O-Ring

Replacement Navigator Control System Release Pin O-Ring
North Part: 85007.21010

$2.40
North Kiteboarding Navigator Bar Elasticised Trim Line

North Navigator Elasticised Trim Line

Top quality, German-made, extremely high wear Dyneema replacement trim line for the Navigator Control System with a special impregnation coating for resistance to abrasion.

Replacement for 2020 and 2021 Navigator Trim Line.
$17.00
North Kiteboarding Navigator Bar Trim Handle and Stopper Ball

North Navigator Trim Handle and Stopper Ball


Replacement for North Navigator Trim Handle and Stopper Ball

* stopper ball does not include set screw

$10.00
North Kiteboarding Navigator Bar Depower Line With Tubing

Depower Main Line (with tubing)


Top quality German-made extremely high wear Dyneema depower line with a special impregnation coating for resistance to abrasion. Comes complete with tubing.

$17.50
PKS - North Pigtail Set (set of 4)
1 of 2

PKS North Pigtail Set

PKS Replacement North pigtail Set. These pigtails connect to the bridle lines coming off the kite and allow you to hook up your flying lines. Always check kite pigtails for wear and tear. Made from 7/64" 100% Dyneema line.

Set Includes:
  • 1 - Red Loop-Loop pigtail with pull tab
  • 2 - Grey Loop-Knot pigtail
  • 1 - Blue Loop-Loop pigtail with pull tab
$19.95
OEM - North Pigtails / Line Connectors (set of 4)

OEM Replacement North Line Connector / pigtail Set. These pigtails connect to the bridle lines coming off the kite and allow you to hook up your flying lines. Always check kite pigtails for wear and tear.

Includes 4 Pigtails, 2 Red, 2 Green.

$15.00
North Hyperflow Inflation Valve - Cap only

The FixMyKite.com North Hyperflow CAP ONLY  is the top screw portion with Cap for the new inflate/deflate screw valve that North now uses on their kites (2020 and Newer). 

This product does NOT include the base or Stick-on patch. This will NOT WORK in the old North Airport Valve base.  It will hook up straight to any standard pump.

This cap will work on Cabrinha Airlock 2, Slingshot Complete Screw, Eleveight Kites.

$11.95
OEM North Hyperflow One Pump Hose - 1 Meter
1 of 2

OEM North Hyperflow One Pump Hose


1 Meter of North Hyperflow Hose. .


This hose works on all North Kites

$14.95